Skip to content
STP · ETP · WTP · RO — Pune, Maharashtra

Upgrade and retrofit

Fix the plant you already have.

An overloaded or failing plant rarely needs to be demolished. We audit it, find what limits performance and upgrade those parts: biology, aeration, settling, filtration or controls.

Typical gain
More capacity in the same tanks
Common upgrade
Conversion to MBBR
Downtime
Planned to keep treatment going
Water treatment plant being upgraded

Overview

Most failing plants have a few root causes.

Plants fail for predictable reasons: the building filled up faster than planned, blowers or diffusers wore out, sludge was not removed, or the original design was too small. Finding the real cause first avoids spending on the wrong fix.

Converting an activated sludge tank to MBBR by adding media is often the most effective upgrade, adding biological capacity in the same tank. Other common fixes are new blowers and diffusers, tube settlers in clarifiers, tertiary filters and better controls.

You probably need this if

  • STP overloaded after full occupancy
  • Treated water fails lab tests
  • Plant smells or foams
  • Tertiary treatment needed for reuse

How it works

The treatment step by step.

  1. 1

    Audit

    Flow measurement, sampling, equipment checks and record review.

  2. 2

    Root cause

    Report showing what limits the plant and what each fix achieves.

  3. 3

    Upgrade design

    Media, aeration, settling, filtration or control changes, with drawings.

  4. 4

    Execution

    Phased work to keep sewage treated during the upgrade.

  5. 5

    Verification

    Re-testing and handover with updated operating instructions.

Upgrade options

What we typically change.

  • MBBR conversion

    Media and screens added to existing aeration tanks.

  • Aeration upgrade

    Efficient blowers, fine bubble diffusers and DO-based control.

  • Settling and filtration

    Tube settlers, pressure sand and carbon filters.

  • Automation

    Panels with timers, level controls and remote alarms.

What you get

Built to run day after day.

  • Capacity without new tanks

    More treatment from the existing civil structure.

  • Lower power

    Efficient blowers and diffusers often pay back quickly.

  • Back in compliance

    Treated water that passes tests again.

From enquiry to handover

One team, start to finish.

We design, fabricate, install and maintain the plant, so there is one point of contact for performance.

  1. 01

    Site survey

    We visit, test the water or wastewater, measure the space and note power, access and discharge points.

  2. 02

    Process design

    Flow and load calculations, treatment train, layout drawing and a clear scope of supply.

  3. 03

    Fabrication

    Tanks, skids, panels and piping built and checked in our Pune workshop before dispatch.

  4. 04

    Install and commission

    Erection, wiring, seeding or start-up, trial runs and operator training at your site.

  5. 05

    Operate and maintain

    Optional operation, AMC visits, spares and performance reports so the plant keeps working.

Faster, more accurate quotes

What to share with your enquiry.

A few details let us size the plant properly the first time. If you do not have them yet, we can measure or test on site.

  • Plant capacity and process type
  • Recent lab reports
  • Photos of the plant
  • Occupancy or production now versus design

Questions we hear

Questions about stp upgrade and retrofits.

Can an existing STP be converted to MBBR?

In most cases yes. Media and retention screens are added to the aeration tank, and aeration is checked and upgraded if needed.

Will the plant need to shut down?

We plan work in stages, often one tank at a time, so treatment continues.

How do we know the upgrade worked?

We test before and after, and the handover includes the results.

Is an upgrade cheaper than a new plant?

Usually, because the civil structure is reused. The audit shows the comparison clearly.

Talk to an engineer

Planning a stp upgrade and retrofit?

Share your flow, water quality and site details. An engineer will reply with the next step, usually a site visit or a sizing call.